Please advice

About Volvo keys programming by dump.

Looking different tool coverage

Compared tango ant tmpro2

Tango does not do keys from 2004

Xc70

Xc60

C30

S60

S80

V70

tmpro2 does

s80 06-09 delphi

v70 06-09 delphi

Question is this what tool covers all other Volvos? Which tango and tmpro2 does not do from year 2004.

Answer:

Option 1: Abrites Diagnostics for Volvo is well-known (Google is your friend to have Abrites Diagnostics for Volvo.)

Option 2: Lonsdor K518ISE Volvo key programmer (Newest tool by Lonsdor and much cheaper)

Can’t find Lonsdor K518ISE in any shop. Its released?

Yes, here: http://www.carobd.de/wholesale/lonsdor-k518ise-key-programmer.html

Update firmware & software on official site: http://en.lonsdor.com/. I can gather that it reads data with a programmer first. Then you sent the data to the support team. They will convert it for you.

Lonsdor K518ISE does:

Volvo (S40, S60, S80, XC60, XC90, C30, C70, V40, V60, V70) key programming.

Details:

Series Origin Year Fuel Type Function

S60 Other Other Other Proximity Key[insert key to start]

S60 Other Other Other Smart Key[one-button start]

S80 Other 09- Other Smart Key[one-button start]

XC60 Other 09- Other Smart Key[one-button start]

S80 Other 09- Other Proximity Key[insert key to start]

XC60 Other 09- Other Proximity Key[insert key to start]

S40 Other Other Other Smart Key

S40 Other Other Other Key Programming

S80 Other -09 Other Proximity Key[insert key to start]

V40 Other Other Other Proximity Key[insert key to start]

C30 Other Other Other Key Programming

C30 Other Other Other Smart Key

V40 Other Other Other Smart Key[one-button start]

S80 Other -09 Other Smart Key[one-button start]

V60 Other Other Other Proximity Key[insert key to start]

V60 Other Other Other Smart Key[one-button start]

XC60 Other -09 Other Proximity Key[insert key to start]

XC60 Other -09 Other Smart Key[one-button start]

XC90 Other Other Other Flip Key

C70 Other Other Other Key Programming

C70 Other Other Other Smart Key

V70 Other 09- Other Proximity Key[insert key to start]

V70 Other 09- Other Smart Key[one-button start]

FYI, the diagnostic box have just released a programmer with volvo coverage , this one gets released next week but im told was being demonstrated at mla show last weekend , also AD are reported to be releasing volvo coverage on their new smart pro being released at end of year , also abrites are adding to their volvo coverage , so at some point you will become spoilt for choice on volvo.

Anyway, Lonsdor K518ISE key programmer for Volvo is working & cheaper one to be your choice.

Lonsdor K518ISE best car key programmer car list. Look here:

Volvo (S40, S60, S80, XC60, XC90, C30, C70, V40, V60, V70) key programming.
Toyota/Lexus: smart key all key lost – via OBD ( without dismantle)
BMW CAS3/CAS3+/CAS3++: direct OBD programming
BMW CAS4/CAS4+: dismantle & read data programming
2016 -New Maserati: smart key programming
2016 -New Ford: smart key programming
Hyundai / Kia 46/47/8A smart key: PIN code reading via OBD, all key lost included.
Renault ( Megane, Koleos, Scenic) without PIN code key programming
VAG group 4th & 5th immobilizer system
Ferrari (458, F12, F149): direct OBD programming
Peugeot /Citroen: two ways to read PIN code & programming, all keys lost included.

Lonsdor K518ISE Immobilizer Car List:

Europe:
Audi, BMW, Benz, VW, Volvo, Citroen, Ferrari, Maserati, Fiat, Lamborghini, Jaguar, MG,
Land Rover, Bentley, Lancia, Opel, Peugeot, Porsche, DS, Renault, Alfa Romeo, Smart,
Borgward

America:
Cadillac, Chevrolet, Dodge, GMC, Buick, Hummer, Ford, JEEP, Lincoln, Mercury

Asia:
Honda, Hyundai, Isuzu, KIA, Lexus, Mazda, Mitsubishi, Nissan, Ssangyong, Subaru, Suzuki,
Toyota, Shigaoka Queen

China:
Iveco, Trumpchi, BYD, Geely, Chery, Great Wall, Young Lotus (Basically all Chinese car
models are included)

Lonsdor K518ISE Odometer Correction Car List:

VW, Porsche, Ford, Jaguar, Land Rover, Mazda, Audi, Renault, Hummer, Hyundai, Kia…

Note: more high-end cars will be updated very soon.

So, Lonsdor K518ISE can be the best key programming machine for all cars.

1st key programmer tool in the world is able to:

Read PIN code to Kia / Hyundai function for Type 46 & 47 & 8Akeys + Add Smart Key without PIN code

Match keys for all Volvo models via OBD

Mazda 3 Angkesaila smart key program (2017)

BYD smart key program without Pincode

Nissan key system (4 Digit Pin Code)

Nissan remote system

Nissan smart key system (New 20 Digit Rolling Pin Code) incl. Qashqai(after 2015), X-TRAIL(before 2013), QX60(after 2013), teana-vip(after 2013), Cima(after 2013), JX35(after 2013)

Toyota Smart Key all lost

Lamborghini Porsche BMW & LandRover Ferrari Models covered

a lot of Chinese vehicles Great Wall Haval Borgward MG Beiqi Foton covered

Introduce Universal Smart Key Emulator:

SKE-LT: Smart Key emulator – Toyota/Lexus smart key for all key lost via OBD
Black: SKE-LT-DST40(94/D4) -Supports 94/D4 smart key.
Red: SKE-LT-8A(88/A8)-Support 88/A8 smart key.
Green: SKE-LT-DST80(98)-Supports 98 smart key.
Blue: SKE-LT-8A(A9)-Supports A9 smart key.

Will announce for once ready in stock, awaiting English version

http://www.carobd.de/wholesale/ske-lt-smart-key-emulator-for-lonsdor-k518ise-key-programmer.html

Detailed Coverage till now

[ World First]

[ World First] Hyundai/Kia smart systems( 46 chip ) added for key learning without pincode

[ World First] Hyundai/Kia smart systems ( 8A chip ) added for key learning without pincode

Volvo S80(before 09 smart key) key program;

Volvo V40 key program

Volvo C30 key program

Volvo V60 key program

[ World First]

Lonsdor K518ISE is tested OK to program Toyota/Lexus smart key all key lost via OBD by working together with extra SKE-LT Smart Key Emulator, as known, before Lonsdor K518ISE, there is no one tool in the Chinese market can do this.

Here we go to deep for instruction and test reports:

1.SKE-LT Smart Key Emulator instruction:
SKE-LT Smart Key Emulator introduces brand new functionality for work with Toyota/Lexus vehicles equipped with Smart Key Systems via OBD, without dismantle. Main objective of the software is to allow addition of smart keys in “all keys lost” situation by creating emulator which allows to get permission to register new keys via diagnostic equipment.

SKE-LT Smart Key Emulator is designed in four colors for different style of smart key.

Black: SKE-LT-DST40(94/D4) -Supports 94/D4 smart key.(optional)

Red: SKE-LT-8A(88/A8)-Support 88/A8 smart key.(optional)

Green: SKE-LT-DST80(98)-Supports 98 smart key.(optional)

Blue: SKE-LT-8A(A9)-Supports A9 smart key. (optional)

http://www.carobd.de/wholesale/ske-lt-smart-key-emulator-for-lonsdor-k518ise-key-programmer.html

1.Press and hold the power button for 2 sec to turn on/off; In start status, when standby for 2 min, the key will automatically shut down; After switching 3 times, the key will be initialized, and can be recycled again.
2.Status indicator: Blue-normal; Red-hardware failure;
3.After receiving the product, please open the back cover of each emulator and install battery first before using it.
SKE-LT Smart Key Emulator Battery standard: CR2032=3V(Please install battery).

Steps to install battery:

Open back cover, then remove main board, finally install battery.

2.Function & Operation
2.1 Function description

Bind emulator key: first use, it is required to bind SKE-LT emulator to K518ISE main unit;

Backup EEPROM data: backup on board computer immodata;

Make emergency emulator key: with the backup immodata to make the designated SKE emulator key to the key that can replace the original master key. Such key can be used to turn on the ignition, then add smart key can be proceed;

Add smart key: to add a smart key.

Delete smart key: to delete a programmed key.

2.2 Function operation

Operation on all key lost situation：

1) Binding

1.Go to the “Bind emulator key” function;
2.Turn on emulator key and put it into K518ISE key slot (put the status indicator down, make sure the key is active);
3.Following the system direction and click “OK” to start binding;
4.After binding completed, the system will indicate “Binding successful”.
2) Backup EEPROM data

Connect K518ISE with car OBD port, enter into “Backup immodata” to back up the data.

3) Make emergency emulator key

After choosing the immo data, in a network environment, the system will indicate to choose the corresponding SKE emulator key model, please start the key and put it into K518ISE key slot(make sure the key is activate), follow the instruction to make an emulator key.

4) Add smart key

Click the car start button, put the generated SKE emulator key close to the start button, with induction the car will automatically activated.

The system will read current key count, then follow the instruction to add key.

Precaution

1.”Bind emulator key” can identify the SKE emulator key binding state;

2.SKE emulator key need to bind K518ISE host and can bind only for one time;
3.When making emulator key, make sure well net connection and to choose the corresponding SKE emulator key model correctly.

Finally, where to have original Lonsdor K518ISE with emulator for Toyota all key lost?

You could get it from http://www.carobd.de, when you google and find the price is the same, why not choose a well-known shop.

original Lonsdor K518ISE on sale:

http://www.carobd.de/wholesale/lonsdor-k518ise-key-programmer.html

How to tell if the K518ISE is the original?

1.Check if the K518ISE is printed with Lonsdor logo like this.

2.original K518ISE is able to update software and firmware on http://en.lonsdor.com/.
3.original Lonsdor K518ISEprice as high as 1029EUR.
That’s all.

Good luck!

Have golf 6 all keys lost to program new keys with Xhorse VVDI2 VW or VVDI2 full version, it is supposed to do service mode, please do as the below procedure.

—–On Kessy system you have to have Kessy Key brand new or Buy form Dealer.

If you use used key and chnage transponder car will start only if you put key close to coil ( where is normaly igntion tumbler is)

Remove dash , Read eeprom with programmer and save originla file.

Do service mode , I do this manual way, open originla file in Hex Editor add at line 1420 and 1430 all FFFFFFF.

This way you do not loose VIN and ABS stay same .

Write molded file back to cluster and put cluster in car.

On Kessy car you need to bridge at OBD pin 1 and 16 to get Ignition On.I would make with little switch because you will need to give ignition On/OFF when learn keys. Connect to cluster and read Sec. block. After susses , you need to write original eeprom to cluster.

VERY IMPORTANT : Do not EXIT any function till all is done.

If you have key form dealer then you can learn it right a way ,If you have New Kessy key then you need to read Immo block again , then make a dealer key .

After this press button ADD KEY. Then choose second option Learn Key with security code and follow instruction.. If you want to learn only 1 key you will see 0-1 then 1-1 .

At it end before you press OK on pop up message you need to turn ignition Off/On After THAT you see 1-1, then press OK on Pop up message and wait till 1-1 goes away. All keys are learn successful.

—–Other way if you have only Used key with new ID48 ,:

Remove dash , Read eeprom with programmer and save originla file.

Do service mode , I do this manual way, open originla file in Hex Editor add at line 1420 and 1430 all FFFFFFF.

This way you do not loose VIN and ABS stay same .

Write molded file back to cluster and put cluster in car.

On Kessy car you need to bridge at OBD pin 1 and 16 to get Ignition On.I would make with little switch because you will need to give ignition On/OF when learn keys. Connect to cluster and read Sec. block. After susses , you need to write original eeprom to cluster.

VERY IMPORTANT : Do not EXIT any function till all is done.

Then read Immo block again ,

Make a dealer key first . After that press ADD KEY , then use frist option add key direct to immo block . After all done reset cluster ,remove bridge on OBD pin 1 and 16 . Put key close to Immo coil and start car.

That is service mode only needed for c32 c64 clusters. Please look at a photo which numbers need do service mode to do all keys lost

Tips to follow:

From 1 to 7. when you have all key lost .

#1 is cars with Micronas dash and for Service mode use VVDI and it needs in most cars made 2007 and up, Before that all key lost will work direct OBD.

#2 it is different service mode that I gave solution is other post

#3 to 7 my solution works in all of them.

Service mode only need if ALL KEy LOST, otherwise read IMMO data and make a KEy LEARn via IMMO DATA FILE

if you confuse what cluster choice, post cluster p/n and manufacture date.

Mercedes Benz W166 all keys lost and program new keys, CGDI MB Pro is good choice, here share user manual with pictures.

Guide:

Select Lock(EIS)

Click on “Read EIS data” then “Computer password”

Click on “Copy key without key” then “Collect Data”.

Prepare to collect data, please wait…

Please insert the simulation key into the lock in 30 seconds.

CGDI MB programmer is collecting data.

Data acquisition succeed, save it by default.

Click on “Upload data” then open the data you saved.

Upload data successfully.

Click on “Query password”

Wait for 2 minutes, query password succeed.

Click on “Lock (EIS)” then CGDI MB display password, copy it.

Click on “Paste password”

To be updated……

Post on TJECU CN900 Mini Toyota G chip token recharge procedure, before do this, you are required to login the official site to bind the device with serial number and active device.

Note:For more auto key programmer,pls visit this website:

http://www.carobd.de/wholesale/auto-key-programmer/

1. Login your member on the cn900 mini official website, click” Personal Center”

2. In my account, please click ” My Device”

3. Click “Bind the new device”

4. Fill out Equipment Model, serial number, purchasing date and remark

5. After you bind the device, please back to home page ,select”product list”and click “Device activation”

6. Click “TOY-G Chip Recharge”, Add to Cart, open your shopping cart, select the purchase products , proceed to checkout

7. Fill out order information (Receiver address, payment way, express delivery are required), when you select the device, please choose the one which you binding, and fill out the check code. If you have no yet binding device, please click “Device Management”, and operate according to step 3 and Step 4.

8. Concluding remarks.

Used SKP1000 key programmer to program 2013 Maserati Gran Turismo smart key, at first the new key can start the car but the remote fail to open the door.

Finally, I found the reason and it worked great.

It’s not a long story, hope it helps.

Go on with the above-mentioned problem, after that I tried to enter “Remote System”, tap “Maserati” but received prompt “Connection fail”.

Screenshots helps a lot to understand what I say.

With a new key to turn.

I didn’t believe it’s true, then I tried one more time, this time I did it, the remote works fine.

Tip for sharing: After complete programming key, do not wait for some time but immediately complete remote, then the remote will open the door successfully.

CGDI BMW FEM BDC key learn is in the dismantling method instead of OBD method. Then you have to know the FEM/BDC system location, 95128 IC location, 95256 IC location and Key learning position, read the detail in the below parts.

1.BMW FEM/ BDC installation location.

2.95128 IC location

3.95256 IC location

4.Key learning position

That’s all.

Value bundle:

CGDI Prog BMW MSV80 plus BWM FEM/BDC Authorization.

XTOOL EZ400 PRO is different from Xtool EZ400 in the VCI box, XTOOL EZ400/EZ400 Pro is different from Xtool PS90/PS80 in the special functions.

1.Different:
1). XTOOL EZ400 PRO = Xtool EZ400 + VCI box

XTOOL EZ400 PRO is all-in-one machine, no need any more VCI box, so it is 2.64LB lighter than Xtool EZ400, lighter package means less shipping cost and easier to use.

Attach Xtool EZ400 VCI box

Attach XTOOL EZ400 PRO full package (without the above Xtool VCI box)

2). XTOOL EZ400 PRO / XTOOL EZ400 functions < Xtool PS90

Xtool PS90 (10inch tablet with wifi and all function):

Full system diagnosis on all makes……confirmed

IMMO……confirmed

Odometer Adjustment ……confirmed

Special functions (Oil Reset/Engine Oil Light Reset, EPB Electrical Parking Brake Adaptation, TPS Throttle Body Adaptation, EPS Electric Power Steering Calibration, Gear Learning, ABS Bleeding , ECU Reset, Tire Pressure Warning Light Reset and Battery Reset.) ……confirmed

XTOOL EZ400 PRO 7″ functions:

Full system diagnosis on all makes……confirmed

Special functions works: Oil Reset/Engine Oil Light Reset, EPB Electrical Parking Brake Adaptation, TPS Throttle Body Adaptation …confirmed

3). XTOOL EZ400 PRO / XTOOL EZ400 is much cheaper than Xtool PS90

Xtool PS90: 1500 dollars to 2900 dollars (google to confirm)

XTOOL EZ400: 554 dollars

XTOOL EZ400 PRO: 419 EUR

SRC: http://www.carobd.de/wholesale/xtool-ez400-pro-tablet-diagnostic-tool.html

2.Same:
■Original Xtool products and update on Xtool official site xtooltech.com.
■Full system diagnosis…… confirmed
■Both can perform these special functions: Oil Reset/Engine Oil Light Reset, EPB Electrical Parking Brake Adaptation
■One-year free update, one-click software update via WIFI
■After-sales technicalsupport (Remote access).

That’s all

Post on how to use OBDSTAR renew key PCF79XX adapter to unlock Audi 5 Generation key by working together with OBDSTAR X300 DP(Orange)/ OBDSTAR key master DP(Green). Besides, OBDSTAR renew key PCF79XX adapter is designed for BMW, VW, Volvo, Chrysler, Renault, GM, Kia, Hyundai etc.

To unlock Audi 5 Generation key, please prepare the two tools:

OBDSTAR renew key PCF79XX adapter

OBDSTAR X300 DP or OBDSTAR key master DP

Guide:

Plug OBDSTAR X300 DP with VCI box, renew key PCF79XX adapter etc shown as below picture, make sure the indicator lights flash.

FYI, OBDSTAR X300 DP (Orange)VS OBDSTAR key master DP(Green):

They are the same tool, they have same function, save vehicle coverage. They differ from each other in color, the orange one X300 DP is supplied on Eshop, so it does not need to waste money to order both two.

Tap X300 DP option “DP” then “Diag Program”.

Tap “Other Function” then “Unlock Key”.

Have option “Renew key V30.01”, click “OK”.

Tap “Audi”, then “5 Generation”

Have 3 options shown as below, go to check the chip board number and tap “Board 233.453.111-05/06

Tap “315MHZ 8T0959754C”

Please refer to the following figure for the correct connecting line.

Pop up “Connect the host to the PCF79XX adapter and supply the 12V power to the adapter.” Tap “OK” and writing data, please wait……

Data Brushing successful, click “OK”

Done