Greetings everyone. Has anyone been able to read this ECM? I can only read the VIN number, but I can’t connect to read the flash and EPROM. I used a 120-ohm resistor with 14 volts.
Solution :
1,Pin 87 should preferably be a 12V pin, not the ignition pin.
2,need to enter the pinout from 17.5.6.
3, Get P003 to work together.
Both CG CG70 and OBDSTAR P50 will do Audi A6 A8 Q5 hybrid high voltage battery BMS crash reset
Which device is better or faster ?
Here is the clue.
CGDI CG70
CG70 will repair Audi BMS module by CAN Mode.
Part Number: 8R0915233,8R0915591
Processor: D76F0192
Here is an example.
Repair problems: Engine don’t start. Hybrid system is locked.
Select part number 8R0915233 and check wiring diagram.
Connect BMS module with CG70, connect CG70 with main cable and 12v power supply.
Connect with the BMS unit and read the fault code P1609
The B1609 fault code in an Audi indicates an “IIIuminated entry input circuit short to battery”.This means the circuit related to the car’s IIIuminated entry feature(e.g. door light,interior light)is shorted to the battery, causing a fault.
Click One-click repair.
Repairing BMS in process
Read module again and you will see that fault P1609 has been erased.
Pros:
Repair by CAN Easier connection.
Built-in algorithms.Supports one-click BMS repair.
Cons:
Less BMS part number coverage.
OBDSTAR P50
P50 will erase Audi BMS module on Bench.
OBDSTAR P50 Audi BMS Support List
You need to connect with P004 adapter on bench,read eeprom and erase BMS crash data.
Problem:
Nissan Sentra 2025. HFM with 10193 CPU. Try to read pin code from dump with Autel IM608 and APB131 adapter, but failed.
Data read correctly, read 3 times, but reading pin failed.
What’s wrong ?
To successfully read pin code from HFM dump, make sure:
If done all above but still failed, use J2534 and Nissan consult online program 3 min done.
User feedback:
It was necessary to update Autel. After the update, the pin code was read and the key was programmed.
The APB131 adapter is compatible not only with Autel MaxiIM IM508/IM608 devices but also with OTOFIX IM1/IM2 euquipment. Today, we will share user feedback and demonstrate how to add a key using the OTOFIX IM2 and APB131. The process is similar to that of the IM608.
It is a Audi Q3 F3 2020. The car was deliered with one key, need to add a spare key.Immobilizer data is stored in the dashboard. The task is to add a spare key to this model with OTOFIX IM2 key programmer.
The process of removing the instrument panel was short. you only need to disassemble half the dashboard and soon it was already lying on the table.
Cluster Number: 83A920800B
Processor
In this case, you need the APB131 adapter(MQB-V850/RH850)
We connect it, supplied additional power to the programmer, and in 7-10 minutes the file was ready
The file needs to be saved, then select”Immo-data” and add the saved file there. After that, you will have the CS and Mac code.
The next step is to prepare the dealer key (2keys)
Then in the menu you need to perform the learning, which is also called”Key adaption” . On the instrument panel at the button, there will be 0/3. Then we apply the keys to the immobilizer coil one by one until there is 3/3.
YANHUA ACDP BMW G Sereis BDC2 Vehicle List
Yanhua Mini ACDP has just released Module 38, a game-changer for BMW G-Series BDC2 immobilizer key programming ! This update makes adding keys faster, safer and fully automated
What’s the vehicle list
| Model | Chassis Number | Year Range |
| 5 Series | G30 | 2016/11-2020/06 |
| 5 Series | G31 | 2017/03–2020/06 |
| 5 Series | G38 | 2017/05-2020/08 |
| 6 Series | G32 | 2017/07-2020/06 |
| 7 Series | G11/G12 | 2015/07-2019/02 |
| M5 | F90 | 2017/11-2020/06 |
| X3/IX3 | G08 | 2018/05-2021/08 |
| X3 | F97 | 2019/04-2021/07 |
| X3 | G01 | 2017/12-2021/07 |
| X4 | G02 | 2018/04-2021/07 |
| X4 | F98 | 2019/04-2021/07 |
| Rolls-Royce | 2018- |
Does it do all key lost ?
No, Add key only .
Is it only for ACDP 2 ?
Works with both ACDP2 and ACDP1
Does it require an extra software license like Autel ?
The module 38 comes with BDC2 interface board + license A503
What’s the difference between YANHUA ACDP BMW BDC2 function and other devices ?
Yanhua ACDP uses BMW BDC2 interface board method Just need to insert the interface board to the BDC2 module directly.
Fully automatic operation, no need to manually plug and unplug connection during operation, safe and stable.
It is mu safter than the OBD method, it is easier than Autel and other devices .
What key to use ?
You can program both original BDC2 key and any blank aftermarket key .
Can change the VIN ?
No, it can not
Add mileage reset for BDC2 ?
Not yet, For add key only. Module 38 does not do mileage function. For G series mileage correction,you may need Yanhua 35xx programmer +simulator chip+ID7/ID8 filter.
For more installation video, please visit following link
First Update:key adding function for BMW F/G chassis models and free on X431 IMMO Scanners
Just upgrade your software with a single tap to enjoy the function!
Second Update: New software updates for SUBARU, PERODUA and VINFAST.
How to add #MQB48 key using MLB-TOOL? No dashboard disassembly required! Read the original key data and easily calculate the immo data via MLB-TOOL and MQB48 Adapter
Xhorse MLB Tool for MLB PN XDMLB0 Work with VVDI2 or VVDI Key Tool Plus No Need Remove Chip
Here we share replacement of MLB-Tool chips
Problem:
Hi..this is on my KeyMaster G3 with ECU Flasher license, has been working great but today I get this msg anytime I hit “Connect” to any ECM, msg comes up right away, first noticed it trying to connect to a Gpec2a but it does this with anything I try to connect to, have a friend with a DC706 and he is getting the same error msg, can anyone shed some light on this issue?
Solution:
The obdstar x300 classic g3 machine seems fine, customer can select P003/MP001 to connect. If customer do not do update, then everything is fine .
