Tag Archive | flex

Flex Update Hyundai Kia SIM2K-510 ECU by OBD (Exclusive Solution)

SIM2K-510 New Exclusive Solution is coming !

New protocol released in Magic MotorSport Flex software version 8.28.0.0 allowing techniancians to program kefico SIM2K-510 units in OBD, following a simple, fast, and more efficient procedure.

Connect, read, modify!

Just connect the OBD cable, down.oad the Virtual Read and start your modifications. If the Virtual Read is unavailable, perform a real read in OBD on Bench mode. The unit will unlock automatically.

Moreover, even CAN FD versions are now supported thanks to the new FLX4.4 adapter

Vehicles: Hyundai ‘ Kia

Working mode: OBD’ OBD on Bench

SOftware: Flex 8.28.0.0

Connection: ~30 seconds

Reading time: ~ 5minutes

Writing time: ~10 minutes

Memories : VR/Read/Write/Checksum Maps

License: FLS0.1M/S FLS0.5M/S

Mode 01 OBD
Connect, read and edit

A simple and fast procedure

01. Connect the OBD cable
02. Download the Virtual Read.
03. Make the changes you need.

Mode 02 OBD on Bench

On the bench, with a real read

When the Virtual Read is not available.

Use OBD on Bench mode to perform a real read of the ECU

Also supports CAN-FD versions.

For versions using CAN-FD communication, Requires the new CAN-FD FLX4.4 adapter

Some of the supported vehicles.

Hyundai Kona (I) OS (2017MY) 1.6L CRDI 16V MHEV 134HP

Hyundai Tucson (IV) NX4(2020MY) 1.6I CRDI 16V 114HP

Kia Ceed(III) CD(2018MY) 1.6L CRDI 16V 134HP

Kia Sportage (V) NQ5(2021MY) 1.6L CRDI 16V MHEV 134HP

Kia Stonic(I) YB(2017MY) 1.6L CRDI 16V 114HP

 

Before Working on a SIM2K-510, CHECK the car and disconnect.

any external alarm system connected to the CAN bus
any SCR/Adblue emulator connected to the CAN bus
any OEM multimedia system connected to the CAN bus
any other device connected to the CAN bus that is not original equipment of the car
if any of these devices is connected, communication breaks and the ECU is permanently bricked. It cannot be recovered

Other precautions

Use a stabilised power supply( about 13v). The unlock does not start below 12.5v
Never interrupt the unlock. The Flex asks for confirmation before starting.
Keep the internet connection active for the whole operation.
CAN-FD versions: writing requires the new CAN-FD adapter FLX4.4 . With a secure Gateway(SGW detected), connect directly to the ECU (OBD on Bench)

Flex Failed to Write PSA SID807EVO by OBD Solution

Problem:
Magic Motorsport Flex programmer reads Peugeot 307 SID807EVO ECU ok, but can not write the modified file by OBD. It is a keyless system.

Error autohrization from ECU failed.


Solution:

The keyless ones have to see the key in the emergency key position to allow operation.

Key must be in a coil detection area, that is why you couldn’t read.

Put key in the correct compartment and try again. Put key in the slot beside the steering.

Also if manual put it in 1st drivers seat belt on and hazards

Optional Solution:

Try leaving the ignition on even when it asks you to turn it off, or disconnect the battery for a while and try again.

Play around with ignition on off timings. Don’t wait for flex, when it says ignition on click ok and then wait around 5-5 seconds before you turn it on. If you’ve done any resets with diag make sure ignition off for 2 minutes before you connect flex
SID87 EVO if password protected can be done obd, if non password protected boot only,, should still connect to update to latest software.

User feedback:
Disconnected battery for some time did the fix and worked